A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
The article down below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is really interesting. Have a go and make your own final thoughts.
Mounting a tub isn't exactly brain surgery, but it does need strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately hard project. If the old tub is easily accessible, the job can relocate rapidly; if you need to open a wall to eliminate the old bathtub and place the new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your restroom if you have currently purchased a brand-new bathtub and do not need to transform the plan of your previous supply of water pipelines.
Your tools and also material checklist ought to consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, after that the first thing you should do is separate the water supply. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be rather bothersome because of the restricted access that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipes. Once the supply pipes have actually been eliminated, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before going on to fit the new faucets, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers are in location in between the faucet and the sink. Secure the faucet in position with the supplier supplied backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Making use of the two wooden boards under its feet, place the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipeline by making a compression join; after that do the exact same for the other tap.
Activate the water supply as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Load the tub as well as likewise examine the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the tub has actually been utilized a minimum of once as this will resolve it right into its final setting.
Getting ready for the Setup
First of all, the supporting structure supplied with the bathroom should be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last position.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split a rigid seal, creating the water to pass through the wall surface in between the bathroom and the tiling, causing issues with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to enable the activity experienced when the bathtub is in use. The sealant can fracture fairly early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles utilizing water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very involved in How to Install a Bathtub and I am praying you enjoyed the blog post. Appreciated our article? Please share it. Let someone else find it. We recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Services Report this page